TITAN
-
Load capacity
156 kg
343.92 lbs
(Load capacity is based on < 10.000 cycles) -
Load capacity
275 kg
606.27 lbs
(Load capacity is based on < 10.000 cycles) -
Width
18,5 mm
0,73 inch -
Height
70.9 mm
2.79 inch -
Travel
full extension 100% -
Travel
over extension 130%
-
Closed position
-
Bumper without hold closed
⨯
Bumper without hold closed
This feature reduces the sound produced when the slide reaches the end of its travel.This bumper does not prevent the slide from opening from its closed position.
-
Bumper with hold closed
⨯
Bumper with hold closed
This bumper prevents the slide from opening by itself in its closed position. It also reduces the sound produced when the slide reaches the end of its travel.
-
Soft close damper - outside
⨯
Soft close damper - outside
This damper is mounted outside the telescopic slide and has a maximum of 100 mm pull in. Furthermore, this damper has a load capacity of 50 kg, but there is the possibility to mount more dampers, and for that reason load capacity will increase. It is tested on 60.000 cycles exceeding LGA standards. This feature is prefered by its extra smooth damping and can be applied with all slides.
- Lock in
-
Pull in 42N - 35mm
⨯
Pull in 42N - 35mm
The mechanism actively pulls the slide into its closed position when it reaches the end of its travel and prevents it from bouncing open again. This feature has an extra long pull in and contains a fail safe function which has the ability to reset itself after incorrect use or incorrect sequencing.
-
Pull in 30N - 22mm
⨯
Pull in 30N - 22mm
The mechanism actively pulls the slide into its closed position when it reaches the end of its travel and prevents it from bouncing open again. This pull in feature contains a fail safe funtion, which has the ability to reset it self after incorrect use or incorrect sequencing.
-
Pull in 54N - 22 mm
⨯
Pull in 54N - 22 mm
This mechanism actively pulls in the slide for the last few centimeters. It also holds the slide to prevent it from bouncing back as a result of the rebound-forces.
-
Spring rubber
⨯
Spring rubber
The spring rubber provides a tension between lock-in feature and stop system of the slide. This means there is no rattling while moving.
-
-
Open position
-
Hold out
⨯
Hold out
The hold-out feature prevents the slide from closing by itself when opened.This system is operated by applying a higher initial force to the application.
-
Hold out disconnection inner profile
⨯
Hold out disconnection inner profile
The hold out disconnect spring is a metal leaf spring that needs to be pressed, so that the inner profile can be removed. In this way, the drawer can be easily removed from the cabinet.
-
lock out disconnection inner profile
⨯
lock out disconnection inner profile
The hold out disconnect spring is a metal leaf spring that needs to be pressed, so that the inner profile can be removed. In this way, the drawer can be easily removed from the cabinet. Furthermore, this feature has a locking mechanism.
-
-
Fixations
-
Studs
⨯
Studs
We have developed different fixations for mounting a slide.
-
Spacer bracket - spotwelded
⨯
Spacer bracket - spotwelded
We have developed different fixations for mounting a slide.
-
Drawer carrier - spotwelded
⨯
Drawer carrier - spotwelded
We have developed different fixations for mounting a slide.
-
Studs threaded
⨯
Studs threaded
We have developed different fixations for mounting a slide.
-
Holes
⨯
Holes
We have developed different fixations for mounting a slide.
-
Countersunk holes
⨯
Countersunk holes
We have developed different fixations for mounting a slide.
-
Press inserts
⨯
Press inserts
We have developed different fixations for mounting a slide.
-
Tabs / bajonets
⨯
Tabs / bajonets
We have developed different fixations for mounting a slide.
-
Slotted strip bracket - spotwelded
⨯
Slotted strip bracket - spotwelded
We have developed different fixations for mounting a slide.
-
-
Systems
-
UDL - Universal Drawer Lock
⨯
UDL - Universal Drawer Lock
The Universal Drawer Lock (UDL) is a locking and anti-tilt mechanism with a pre-determined 25 mm pitch dimension, lockable at every position. The UDL fulfills many security and safety related issues. Furthermore it prevents misuse and accidental self locking if it is not used in a proper way. The UDL is a customized locking bar and anti-tilt system for toolbox cabinets. It is suitable for drawer loads up to 300 kg.
-
Soft close column
⨯
Soft close column
Our soft close column system has a maximum of 115 mm pull in lenght and a maximum of 120 kg load capacity, which is practical for heavy storage for example a cabinet in the kitchen. Thanks to our highly qualified staff, the system has an extra smooth movement and is applicable with all slides.
-
-
General
-
Electric discharging
⨯
Electric discharging
Our discharging feature assures a good electical condution between the drawer and the frame or cabinet. This makes the drawer grounded/earthed.
- Protective end cap for drawer profile
- Noise reduction
-
-
Surface treatments
- Bright Zinc Chromate - Black passivation
- Bright zinc chromate - blue passivation
- Electrodeposited coating
- Supports loads up to 275 kg
- Add features such as bumper with or without lock-in, hold/lockout mechanisms, electric discharging and noise reduction
- Add fixations such as abs, holes, press inserts, drawer carriers or threated studs
- The Titan drawer runner can be incorporated into our UDL and Soft Close Column system
Please visit the product features tab on the product page to find out more information about our customizations. In case of customization or a question about the slide, feature or functionality please contact a sales manager.
Load capacity
Load capacity varies as a result of a number of factors. The main factors being the type of slide, length, and ratio between pull-out length and closed length. Another important factor is the number of cycles the slide is required to make. Thomas Regout distinguishes the type of usage between dynamic use and static use. Other factors that influence the load capacity are the features the slide is equipped with, and how it is mounted. Slides are usually mounted sideways so all data concerning load-capacity will be given for side mounted use. For information about the load capacity with bottom-mounted slides, please contact our sales department.
Dynamic load capacity
In order to determine the dynamic load capacity, all types of Thomas Regout slides have been tested for 100,000 cycles. Their maximum load capacity is compliant with, or exceeds, all common national and international standards including DIN, BIFMA, BS, EN and JIS. The dynamic load capacity figures can be found in the graph below.
Static load capacity
Static load capacity is based on test results at 500, 1000 and 10,000 cycles. This is most common for industrial purposes. The static load capacity is considerably higher than the dynamic load capacity for all slides. The static load capacity figures listed below were determined for a single length of that slide and are for indication purposes only. Specific applications can be assessed by our R&D department and tested if necessary.
Extension
Extension is defined as the ratio of the travel length of the slide (T) and the length of the slide in a closed position (L): T = (T/L)*100%. The influence of the extension and length of the slide on the load capacity is shown in the graph below
Thermal resistance
Maximum temperature approx. 100°C, determined by applied plastics and lubrication.
Minimum temperature approx. -20°C, determined by applied plastics and lubrication.
Attention: maximum and minimum temperature are strongly determined by the specific application; duration of exposure, impact and other forces on slide and slide components etc. Values mentioned are indicative, it is important to judge each individual application.
Materials
Thomas Regout slides are available in numerous materials and coatings. Below is an overview of all the materials used in our slides. All our products are compliant with EU ROHS standards.
Sections:
- Cold rolled, low carbon and high yield strength steel according to EN 10268 and EN 10139
- Pre-galvanised low carbon and high yield strength steel according to EN 10147 and EN 10139
- Stainless steel according to EN 10088-2 and EN 10259
Ball cages: Electrolytically galvanized, cold rolled, low carbon and high yield strength steel according to EN 10131 and EN 10152
Ball bearings: Hardened carbon steel C15, Kl 4 DIN 5401
Locking features: PA, PE, PBTP, TPU, EPDM
Sequence devices: PA, TPU, PP Bumpers: RR PA, TPU, EPDM
Lubrication: Heavy-duty ball bearing grease (free of lead), based on mineral oil
Stainless steel
More and more telescopic slides are used in new applications which requires very high corrosion resistance. Due to this fact, Thomas Regout has created the possibility to supply its total product range in stainless steel according to EN 10088-2 and EN 10259. Please inform us about your requirements to create the slide you need. Surface treatment: our slides are available in a selection of standard finishes to the specifications listed below. If you require an alternative or specialized finish not listed, please contact us for further information
Surface treatment (finishing)
Our slides are available in a selection of standard finishes. These finishings can be found in the feature list. The overview provides information about which slide can have a specific surface treatment. If you require an alternative or specialized finish not listed, please contact us for further information.
EU
General downloads
DWG downloads
PDF downloads
STEP downloads
